EXACTLY HOW TO TROUBLESHOOT AND FIX AN ELECTRIC HOT WATER HEATER

Exactly how to Troubleshoot and Fix an Electric Hot Water Heater

Exactly how to Troubleshoot and Fix an Electric Hot Water Heater

Blog Article

Give Me A Quote!

We've encountered this post relating to What Would Cause My Electric Water Heater to Stop Working? below on the internet and decided it made sense to relate it with you on this page.



Numerous modern-day houses make use of an electrical water heater for their heater, due to its ease and convenience of use. However, similar to any other electrical devices, issues might arise with its use, unexpectedly. It can be truly frustrating to get up to a cool shower instead of a hot one or having your bathroom with water that isn't hot sufficient or perhaps too warm. Whatever the case may be, hot water heater problems can be rather aggravating. Thankfully, we have actually made a checklist of possible options to your hot water heater issues. There are a variety of factors that might trigger much of these problems, it could be a problem with the power supply, the electric burner, or the thermostat. Prior to doing anything, ensure you turn off the main power supply for security. Whatever the issue is, getting it dealt with need to not pose too much of a problem if you comply with these actions:

Inspect Your Power Supply:


As standard as this might appear, it is really necessary. Without adequate power, your water heater will not work. So the first thing to do when your water all of a sudden stops working is to confirm that it isn't a power problem. Check if the fuse is blown out or the circuit breaker tripped. If the circuit breaker is the issue, simply turn it off and on again. Replace any broken or worn-out fuse. Test the appliance with power after these changes to see if it's now working.

Examine the Burner in the Hot Water Heater:


If it's not a power trouble, after that attempt taking a look at your burner if it is still functioning. Examine each of your burner to ensure the trouble isn't with any one of them. If any of them is defective, replace that part and then examine whether the warm water is back on.

Inspect Your Thermostat:


If your water heater still isn't functioning or the water appearing isn't hot enough, you may require to examine the temperature level settings on your upper thermostat. Ensure the breaker is turned off prior to doing anything. Open the gain access to panel and press the red button for temperature level reset over the thermostat. This must help heat the water. Transform the breaker back on as well as check if the trouble has actually been fixed.

Call A Specialist:


If after changing all malfunctioning components as well as resetting your temperature, the water heater still isn't working, you might require to call a professional plumber for an expert opinion. The problem with your heating unit could be that the hot and cold faucets have actually been changed or it might be undersized for the quantity of hot water required in your house. Whatever the case might be, an expert plumber would aid fix the problem.

Verdict


Water heater problems are not constantly major. Most of them are because of minor concerns like a blown fuse or damaged heating element. Changing the faulty parts should suffice. Nonetheless, if you are still not able to resolve the trouble, give a call to your nearby plumber to find to get it dealt with.

8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/


No Hot Water — Water Heater Repair

I was introduced to that report on No Hot Water — Water Heater Repair from an associate on our other web blog. Sharing is nice. Helping people is fun. Many thanks for your time. Please check up our website back soon.




Quote & Schedule

Report this page